تمام شد

ماژول شارژر / دشارژر باتری لیتیومی دارای دو خروجی 5V 1A / 2A USB مناسب برای ساخت پاور بانک

1. Charging part:
 1.1 Input voltage5V / 1000mA
 1.2 constant currentWhen the battery voltage is ≥ 3.1V: 1000mA ± 100mA
 1.3 constant pressure4.20V ± 1%
 1.4 Saturation conditionsVoltage ≥4.15V and current ≤ 100mA

2.LED light display part:

 2.1 on the internal charge power display
(A total of 4 lights)
Voltage ≥3.10VLEED: D1-D2-D3-D4 flash
Voltage ≥3.60VLED: D1 light .D2-D3-D4 flash
Voltage ≥3.8V  LED: D1-D2 bright .D3-D4 flash
Voltage ≥3.95VLED; D1-D2-D3 bright .D4 flash
Voltage ≥4.15VLED; D1-D2-D3-D4 light  
 
2.2 Not Charged Click the button to view the powerVoltage <3.0VLED: D1 off (output off)
Voltage ≥3.1VLED: D1 light
Voltage ≥3.70V  LED: D1-D2 bright  
Voltage ≥3.77V  LED: D1-D2-D3 bright  
Voltage ≥3.92VLED: D1-D2-D3-D4 light
 
2.3 external discharge power displayVoltage <3.0VLED: D1 off (output off)
 Voltage ≥3.1VLED: D1 flash
Voltage ≥3.70V  LED: D1 light .D2 flash
Voltage ≥3.77V  LED: D1-D2 bright .D3 flash
Voltage ≥3.92VLED: D1-D2-D3 light .D4 flash
 
3. Discharge part:
 3.1 Output voltage5.0V-5.3V
 3.2 Load output currentUSB2.0 volume standard female base output 1.0A and 2.1A.  
 3.3 Discharge efficiencyAverage efficiency ≥80%
 3.4 short circuit protectionOutput short circuit automatically turn off the output and shutdown, short circuit after the release of charge can be activated.
 3.6 5V output connectorUSB2.0 standard female output.
 
4. White light part:
4.1 No
 
5. Key section:
5.1 sleep mode, press the button to display the current power, 15S after the closure of the LED, a load is boost, no load 30S automatically shut down into sleep mode.
 
6. Battery protection board:
 6.1. Overcharge protection voltage5.0V-5.3V
 6.2. Over discharge protection voltage2.5V ± 50mV
 
7. side charge side part:
 7.1 does not support edge loading.
 
8. Other:
8.1 Machine static power consumption≤ 100uA
8.2 Shutdown voltage≤3.0V
8.3 Starting voltage> 3.3V (charge the second light flashes before external discharge)
8.4 input interfaceMICRO female seat

9, aging test
1, the test steps:
①, assembled semi-finished products, with 20W / 5R resistive load will be put (1A load).
②, will be finished the finished semi-finished products, with a 5V / 1A charger to charge it, observe the status of the display and whether the same OK.
③, will be fully charged semi-finished products, with 20W / 5R resistor load on its discharge, observe the status and specifications are consistent OK, the test is completed.
④, will be finished finished semi-finished products, with a 5V / 1A charger to charge, to reach 70% stop charging, can be assembled products.
⑤, assembled after the finished product, with 20W / 5R resistive load and 5V / 1A charger to do charge and discharge testing to prevent damage during assembly.

نظر بدهید

توجه: HTML ترجمه نمی شود!
    بد           خوب
کد امنیتی

ماژول شارژر و دشارژر باتری لیتیومی دارای دو خروجی 5V 1A / 2A USB مناسب برای ساخت پاور بانک XZD-M1859-V4

  • کد محصول: XZD-M1859-V4
  • موجودی: تمام شد
  • کد انبار: 200816
  • 18,900تومان


برچسب ها: ماژول برد پاوربانک